LED Flex Strip/5050SMD /12V/30PCS/M/Waterproof /Green

Flexible LED strip is a high-end interior/exterior lighting , its LED type by SMD3528, Flexible LED strip adopt high light-emitting devices with high efficiency, long life,light,healthy no strobe, no radiation, environmental protection, to facilitate vecycling. 
Features:
1. Using the high quality and super bright .Epistar chip
2. PCB.is 10mm &12mm width,  Perfect heat  dissipiation.
3. Long lifespan. More than30,000 hours.
4. Safety.  working voltage is DC12V and DC24V.
5. Different colors are available. Warm White,Neutral White,Cool White,RGB,Yellow,Red,Blue,Green, Pink,Purple and so on.
6. .It is easy to adjust  the length. Every 3pcs LEDs are cuttable. The cutted strips can be connected again by special connector.
7. It is easy to be installed. There are 3M tape on the back of strip. 
8. It is flexible and very thin. Only 2-3mm. Can be used nearly any where.
9. .Not only can be use indoor but also outdoor. Because IP20/IP65//IP68 are available.
10. Using PU glue. It is environmental friendly




 
Application
1: Architectural decorative lighting 
2: Archway, canopy and bridge edge lighting 
3: Amusement park, theater and aircraft cabinet mood lights
4: Emergency hallway lights
5: Auditorium walkway light
6: Stairway accent lighting 
7: Concealed lighting 
8: Backlighting for signage letters 
9: Channel letter lighting 
10: Emergency exit path lighting 
11: Cove lighting 
12:Edge-lit acrylic panel lighting
 
Installation instructions:
 
1.The strip have 3M tape on the back.Tear down protective film when installation and stick to the position you want. 
 
2. The Single driver can drive at most two pieces of strips one time,But need to add power and drive circuit when excess two pieces.
 
3. The method of calculate the Power consumption and design of electricity distribution: the quantity of LED strip x single strip power(Proposed that power margin should be left optional, using by 80%,used by 80% rated power.)
 
4. Making sure that output DC voltage of power supply is matched to rated voltage of strip.Please don't light the strip with AC220V directly.
 
5: Eusure the strip is installed solid and reliable.You'd better use specialized super 3M tape to fasten.
 
6. Please mark the scissors label cut, such as outdoor installation, you must make waterproof measure in the middle of wiring.
 
7:Please don't overbending and pull the strip,the minimum angle should not less than 10 degree. The strip is 3leds a cut with 12 voltage.
 
8. The strip must be installed in the anti-static environment,and the operator is advised to wear wrist strap . Work environment should avoid strong acid and alkali object
 
 
 
 



  Flexible LED strip is a high-end interior/exterior lighting , its LED type by SMD3528, Flexible LED strip adopt high light-emitting devices with high efficiency, long life,light,healthy no strobe, no radiation, environmental protection, to facilitate vecycling. 
Features:
1. Using the high quality and super bright .Epistar chip
2. PCB.is 10mm &12mm width,  Perfect heat  dissipiation.
3. Long lifespan. More than30,000 hours.
4. Safety.  working voltage is DC12V and DC24V.
5. Different colors are available. Warm White,Neutral White,Cool White,RGB,Yellow,Red,Blue,Green, Pink,Purple and so on.
6. .It is easy to adjust  the length. Every 3pcs LEDs are cuttable. The cutted strips can be connected again by special connector.
7. It is easy to be installed. There are 3M tape on the back of strip. 
8. It is flexible and very thin. Only 2-3mm. Can be used nearly any where.
9. .Not only can be use indoor but also outdoor. Because IP20/IP65//IP68 are available.
10. Using PU glue. It is environmental friendly




 
Application
1: Architectural decorative lighting 
2: Archway, canopy and bridge edge lighting 
3: Amusement park, theater and aircraft cabinet mood lights
4: Emergency hallway lights
5: Auditorium walkway light
6: Stairway accent lighting 
7: Concealed lighting 
8: Backlighting for signage letters 
9: Channel letter lighting 
10: Emergency exit path lighting 
11: Cove lighting 
12:Edge-lit acrylic panel lighting
 
Installation instructions:
 
1.The strip have 3M tape on the back.Tear down protective film when installation and stick to the position you want. 
 
2. The Single driver can drive at most two pieces of strips one time,But need to add power and drive circuit when excess two pieces.
 
3. The method of calculate the Power consumption and design of electricity distribution: the quantity of LED strip x single strip power(Proposed that power margin should be left optional, using by 80%,used by 80% rated power.)
 
4. Making sure that output DC voltage of power supply is matched to rated voltage of strip.Please don't light the strip with AC220V directly.
 
5: Eusure the strip is installed solid and reliable.You'd better use specialized super 3M tape to fasten.
 
6. Please mark the scissors label cut, such as outdoor installation, you must make waterproof measure in the middle of wiring.
 
7:Please don't overbending and pull the strip,the minimum angle should not less than 10 degree. The strip is 3leds a cut with 12 voltage.
 
8. The strip must be installed in the anti-static environment,and the operator is advised to wear wrist strap . Work environment should avoid strong acid and alkali object
 
 
 
 



 

Audible And Visual Alarm

Audible and visual alarm is set up to meet customers' special requirements for alarm loudness and installation location. At the same time, two alarm signals, sound and light, are issued. Special fields: iron and steel metallurgy, telecommunication towers, hoisting machinery, construction machinery, ports, transportation, wind power generation, ocean-going ships and other industries; it is an accessory product in the industrial alarm system.

emergency alarm,Audible Visual Signals,Visual Alarm devices,sound and light siren,visual alarm system

Taixing Minsheng Electronic Co.,Ltd. , https://www.msamplifier.com