Virtual surround processor chip MM1454

Virtual surround processor chip MM1454

MM1454 is a Q Surround virtual processor IC developed by Mitsubishi Corporation, which can realize the sound algorithm developed by Q SOUND Labs. When the stereo signal with Dollby Pro logic coding in the left / right (L / R) channels is input to the chip, a virtual speaker on the back can be generated. In this way, only using the left and right speakers can realistically reproduce the 3D sound. For normal stereo signals, MM1454 uses Q Xpander technology, which can still produce a deep and wide range of sound effects. Due to the use of active filters, the MM1454 requires few external components and has the advantages of small size and low cost.
The internal structure of MM1454 is shown in Figure 1.

Figure 1 MM1454 internal structure diagram

The MM1454 is available in a 16-pin SOP package. The pin functions are listed in the table.
The noise suppression signal of MM1454 is output to pin 4 (DTE pin), which can turn off the power supply of the power amplifier. Before turning off the power of the IC, by turning off the power amplifier connected to the last stage inside the IC, the noise during the voltage drop of the power supply can be suppressed or even eliminated.
MM1454 has a wide range of applications in TVs, stereos and active speakers. Figure 2 shows its typical application circuit. The power supply current ICC = 16mA, the output noise voltage is typically 15μVrms, the typical total harmonic distortion rate THD≤0.1%, and the voltage gain is typically 10.5dB (VIN = 0.75Vrms, f = 1KHz, SW1 turns on contact B).
In Figure 2, the input signal of the left / right two channels with a typical value of 0.75Vrms comes from the output of the pre-amplifier in the previous stage. The two output signals on pin 6 and pin 7 of MM1454 are sent to the next-stage audio power amplifier circuit through a 22μF coupling capacitor. Connect a 100μF smoothing capacitor and a 0.1μF bypass capacitor between the 9V power supply voltage Vcc and ground. When the switch SW1 on pin 3 is grounded (connecting contact B), it is in bypass mode; when SW1 is connected to a 5V power supply (connecting contact A), it is in Q Surround mode. In Q Surround mode, a current of about 350μA flows into pin 3. The squelch suppression signal is connected to pin 4 to turn off the power supply of the power amplifier. The 10μF capacitor connected between pin 2 and ground can reduce the noise when the power is turned on. The tolerance of the external filter resistors for pins 5 and 9 to 13 is ± 1%, and the capacitor tolerance is ± 5%.

Table 1 MM1454 pin functions

Pin	symbol	Features
1	RIN	Left channel input
2	MUTE	Squelch suppression
3	B / Q	Q SUurround bypass
4	DET	Vcc shutdown detection
5	QF6	(Qf1-Qf6) filter pin
FFFFFF	QF5
10	QF4
11	QF3
12	QF2
13	QF1
6	ROUT	Right channel output
7	LOUT	Left channel output
8	GND	Ground
14	VREF	Reference voltage
15	LIN	Left channel input
16	Vcc	voltage

Figure 2 Typical application circuit of MM1454

Rigid PCB Assembly =  Rigid Printed Circuit Board Assembly, which means the PCB Board is rigid. For rigid PCB , if need be SMT assembly by machine, just need to add tabs/boaders on the PCB board for assembly. Zhongfeng would manufacture the rigid PCB boards follow the design file, source the components follow the BOM file and do the PCB Assembly job follow the assembly drawing and the pick&place file. After PCB assembly done, the components would be mounted on the PCB boards tightly and connected each other through the copper circuits. We call such board as PCBA board or rigid custom PCBA board.

 

Depends on the components assembly types, it have THT PCB assembly, SMT PCB Assembly , one sided SMT and THT PCB assembly, two sided SMT and THT PCB assembly.

 

Depends on the PCB type, it have Rigid PCB assembly, Flex PCB Assembly and Flex-Rigid PCB Assembly.

 

Also we would call some PCB assembly types as Prototype PCB Assembly, Mass PCB Assembly , Turnkey PCB Assembly, LED PCB Assembly and BGA PCB Assembly , etc.

 

With our 15years professional experience, we are available for all types of PCB assembly service from prototype to mass production, available for 01005, 0201, 0.3mm BGA, 0.3mm QFP.

PCB Assembly Capabilities

PCB Assembly Products Show

PCB SMT Assembly Factory Show

Rigid PCB Assembly

Rigid PCB Assembly,Rigid PCB Assembly Prototype,Rigid PCB Board Assembly,OEM Rigid PCB Assembly

ZhongFeng Electronic Technology Co., Limited , https://www.dopcba.com