Lynx Box Exchange Group: 488173725
Specific solution:
I. Check if the battery of the remote control is not powered. Press the power button. If the power of the remote control is off, the power supply is insufficient (if there is a small amount of power, the light will be on but the button operation is invalid). The battery can be removed and reloaded. Try it out or replace it with a button battery.
If the battery is normal, try the remote control again.
Second, try to re-code
Lynx Box Matching Method:
Unplug the power of Lynx Box; press the “Volume+†and “Volume-†keys on the remote control at the same time, do not let go and keep this state, and plug the power of Lynx Box at the same time; Lynx Box is powered on, When you see the kitty moon fishing start screen on the TV screen or the kitten wriggles (preferably to this interface and then release), you can release the two keys of the remote control; at this time, the remote control LED The red light flickers and the code starts. When the code is successful, the red light will only go off after a few flashes.
Pairing is completed, if not, it may be that during the distribution process, the buttons are released, and no pairing is done. Then, retry the steps above.
Precautions:
Put the battery in. Note that the positive “+†is facing upwards. After installing the battery, close the battery cover and tighten it clockwise.
Test whether the remote control is powered on: On the left side of the remote control, near the power button, there is an LED indicator. Press the red POWER button. If the lamp is lit red, the remote control itself is powered and the battery is not installed. The indicator lights of the other keys of the TMB-100A will light, and the indicators of the other keys of the TMB-100E and TMB-100C will not light up; the model of the box can be viewed on the back of the box.
Lynx Box 1s code method:
With the box (50 cm), long press the OK button + return button light, it will flash three times, after three flashes, the code is successful.
Next: Lynx's box connected external audio, power amplifier problems! Pro-test valid
Install sofa butler: http://app.shafa.com/shafa.apk , the perfect companion for Lynx Box!
Waterproof Vertical Mount D-Sub Connectors
waterproof D-sub system is IP67 rated. These panel-mount connectors are available in solder cup as well as right angle and vertical PCB mount types. The cable-mount connector kit includes the connector, which has solder cup contacts. These connectors are available in 9-, 15-, and 25-positions in standard density and 15-, 26-, and 44-positions in high density. The recommended wire gauge for the solder cup connector is 22 AWG to 26 AWG.
These panel-mount waterproof D-subs are designed for rear-mount applications in panels that are up to 2.0 mm thick. They come with two sets of jackscrews. One jackscrew set is 5 mm long for panel thickness up to 1.2 mm, and the other is 6 mm long for panel thicknesses from 1.2 mm to 2.0 mm.
Cable mount D-sub connector kits come with the backshell, seal, thumbscrews, and solder cup connector. They are also easy to install. Simply fit the cable through the backshell, terminate the wire to the solder cup contacts, and hand tighten the cable nut on the rear of the backshell. The backshell will seal a particular range of cable diameters depending on the position count of the connector. Consult the datasheet for specific cable diameter ranges.
Specifications
Current rating
Standard D-sub: 5 A
Hi-density D-sub: 2 A
Breakdown voltage: ≥ AC 500 V/1 minute
Insulation resistance: ≥ 500 MΩ @ DC 500 V
Contact resistance: ≤ 20 mΩ
Material
Contacts: copper alloy, gold-plated
Connector body: nylon 9T or PBT, UL Recognized
Shell: steel, nickel-plated
Applications
DV camcorder
DV VTR
Non-linear editing system
Broadcast monitor
Betacam deck
Panel Mount Waterproof D-Sub Connectors:
Water Proof D-Sub, Standard Density, Male, Panel Mount
Water Proof D-Sub, Standard Density, Female, Panel Mount
Water Proof D-Sub, Standard Density, Female, PCB Mount
Waterproof solder cup, stamped & formed contact D-sub waterproof
solder cup,machined contacts D-sub waterproof
Vertical Mount Waterproof D-Sub Connectors:
Combo Power + Signal D-Sub Connector, Vertical Mount, Pluge Type,
right angle D-sub waterproof
IP67 rated Combo power D-sub waterproof
Standard Density, Waterproof Vertical Mount D-Sub Connectors, High Density Waterproof Vertical Mount D-Sub Connectors,IP67 D-Sub Connectors Vertical Mount,Board Mount Waterproof Vertical Mount D-Sub Connectors
ShenZhen Antenk Electronics Co,Ltd , https://www.antenk.com